Metal Roof Cost in Newark, Ohio
By HM Metals
These are the questions Newark homeowners ask us most about metal roof pricing. Here are honest answers, the published ranges we point people to, and what actually moves a number once we are on the roof.

What moves a quote
A per-square-foot range is a starting point. Your price comes from these:
- Roof surface area
- Measured on the roof, not from floor size.
- Pitch
- Steeper roofs take more time, safety setup and material.
- Deck condition
- Soft or rotted decking has to be fixed first.
- Details
- Valleys, chimneys, vents, skylights and walls add trim and labor.
- Tear-off
- Removing old layers adds labor and disposal.
Question 01
How much does a metal roof cost on a typical Newark house?
Published Ohio budgeting ranges land around $7 to $16 per square foot installed. Roofing Brief (opens in a new tab) lists metal at $7 to $15 per square foot, and Cornerstone Roofing and Siding (opens in a new tab) lists $8 to $16. Exposed fastener panels usually sit toward the lower end, standing seam toward the higher end.
Those are third-party ranges for budgeting. They are not HM Metals prices and not a guaranteed Newark average. Multiply by your actual roof surface area, not your home's floor size; overhangs and pitch make the roof bigger than the footprint.
Question 02
Is standing seam worth the extra cost over exposed fastener?
Standing seam costs more upfront. You are paying for concealed fasteners, a clean look, and less fastener maintenance over time. There is no fixed percentage premium; how much more it costs varies with the panel, the roof and the details. McElroy Metal (opens in a new tab) explains why the price runs higher.
Exposed fastener roofing is a solid, economical choice, but the screws and gaskets need periodic checks. Standing seam still needs maintenance too, just less of it at the fasteners. Sheffield Metals (opens in a new tab) has a good side-by-side.
Question 03
Do I need a permit for a metal roof in Newark?
It depends on who has jurisdiction over your address. Licking County guidance dated May 15, 2026 (opens in a new tab) covers asphalt shingle replacement: a straightforward replacement needs no approval through that office. Replacing at least 50% of the existing roof sheathing or decking, at least 50% of the dimensional lumber rafters, or one or more pre-engineered roof trusses requires approval and inspection.
That guidance applies only within the county building jurisdiction and is about shingles. It is not blanket guidance for the City of Newark. For a Newark address, confirm the authority having jurisdiction and its requirements for a metal conversion with the appropriate building department.
Question 04
Can you put a metal roof over old shingles?
Yes, when the roof is suitable. HM Metals installs both standing seam and exposed fastener metal over shingles. Having only one layer is not enough on its own: the substrate has to be dry and sound, and the existing layers, structure, manufacturer details and code approval all have to allow it. We inspect before deciding.
Going over avoids tear-off, which can make an exposed fastener layover competitive in price with a shingle replacement. Whether it does on your roof depends on what we find.
Question 05
Furring strips or direct over the shingles?
We do both. Panels can go on furring strips, or over a compatible synthetic underlayment or separation layer laid over the shingles. We decide after inspection and follow the panel manufacturer's moisture, ventilation and fastening details for that roof.
Question 06
Can new shingles go over old shingles?
Not with us. Every HM Metals shingle roof is a full tear-off. See shingle roofing.
Question 07
Can I buy metal and install it myself?
Yes. We sell panels, trim and fasteners from our Saint Louisville shop. See material sales.
Sources
- Roofing Brief: Roof replacement cost in Ohio (opens in a new tab) (metal $7 to $15 per sq ft)
- Cornerstone Roofing and Siding: Ohio roofing guide (opens in a new tab) (metal $8 to $16 per sq ft)
- McElroy Metal: Why standing seam costs more (opens in a new tab)
- Sheffield Metals: Standing seam vs exposed fastener (opens in a new tab)
- Licking County: Shingle replacement guidance, May 15, 2026 (opens in a new tab)
